Vestil S-CB-118 Instrukcja Użytkownika

1 OPERATION & SERVICE MANUAL S SERIES STACKER WITH POWERED DRIVE & POWER LIFT Vestil Manufacturing Corp. 2999 North Wa

10 OPERATION Visually inspect stacker for damaged and worn parts, before stacker is taken into operation. Authorized person should read

11 Operation

12 Operation

13 Operation Driving  Pull up the red push button

14 To raise and lower The following are generally valid for the lifting and lowering procedure:  The red operating button of the EME

15 Travel The butterfly switch controls the direction and speed of the lift truck. Rotating the butterfly control towards th

16 Operation Lifting load CAUTION!  Before lif

17 Operation Driving on sloping surfaces 

18 Maintenance and repair TROUBLESHOOTING GUIDE -- ______ Warning: Before performing any task, always block drive wheel off of the ground. Cons

19 Problem: Possible cause(s): Action: Unit will not go forward, or reverse, but belly switch still functions properly. Broken wire, or l

2 General Read and follow the instructions

20 Problem: Possible cause(s): Action: Unit will not reverse; belly switch does not function; forward ok Broken wire, or loose connection, bad

21 Problem: Possible cause(s): Action: Unit will not raise; motor does not run Loose wire Bad solenoid Upper limit switch out

22 Problem: Possible cause(s): Action: Unit will not reverse; belly switch does not function; forward ok Broken wire, or loose connection, bad

23 Filename: Changing Batteries in S-62 Stacker

24 Troubleshooting: If the unit does not operate, check all of the wiring connections to make sure they’re both mechanically and electrica

25 Filename: Changing Motor Controller in S-62 Stacker

26 Filename: Changing Motor Controller in S-62 Stacker

27 Filename: Changing Motor Controller in S-62 Stacker

28 Filename: Changing Motor Controller in S-62 Stacker

29 Filename: Changing Motor Controller in S-62 Stacker

3 Specification SPECIFICATION S-62-FF S-62-AA S

30 Filename: Changing Motor Controller in S-62 Stacker

31 Filename: Changing Motor Controller in S-62 Stacker

32 Filename: Belly Switch trouble shoot

33 Filename: Belly Switch trouble shoot

34 Model: S-62-AA/FF/FA S-62-XX; verify this is the unit you are working on. Make sure E-switch is off (pushed down). Fig.2

35 Filename: Belly Switch trouble shoot

36 VESTIL MFG. CO. Model: S-62-AA/FF/FA This is the bottom side of the tiller handle. 3 allen head screws need to be removed. Fig5

37 VESTIL MFG. CO. Model: S-62-AA/FF/FA Carefully pull the belly switch back off of the tiller while tipping the front up. Fig 7

38 VESTIL MFG. CO. Model: S-62-AA/FF/FA The tiller assembly cover should come off, just be careful not to drop it and rip out the wiring

39 Filename: Belly Switch trouble shoot

4 CCOONNTTEENNTTSS General ………………………………………………………………………………… 2 Specification …………………………………………………… 3 Receiving instructions ……………………………………………

40 Filename: Belly Switch trouble shoot

41 Model: S-62-AA/FF/FA To remove the red cover, use a small screwdriver and carefully lift the plastic up over the gray nub. Fig 14 D

42 Model: S-62-AA/FF/FA This should expose a spring. This spring has a specific orientation. When assembled the spring sets in the red

43 VESTIL MFG. CO. Model: S-62-AA/FF/FA Another picture of the nub, spring not shown. At this point, verify the solder joints are in t

44 Model: S-62-AA/FF/FA The spring can be pushed into position. Fig. 20 This is the spring shown not seated completely. Push the

45 Install bushings. Fig22 Put throttle thumb wheels back on. Fig23 Filename: Belly Switch trouble shoot

46 Install Philips screw. Fig24 Re-installing the tiller cover is basically reversing steps Fig 5 thru 9; with the followi

47 Black nub for right side shown here; and the next photo fig 26 The red tab slides over the top of this black nub on each side when in

48 This shows sliding the red tabs over the black nub. This is basically the reverse of Fig7. Fig29 This is the top

49 Model: S-62-AA/FF/FA Gently push the tiller throttle assembly in place. Again, it’s just reversing steps 5 through 9 to get the t

5 Receiving Instructions Every unit is thoroughly tested and inspected prior to shipment. However, it is possible that the unit may incur dama

50 1) Frayed wires 2) Oil leaks 3) Pinched or chafed hoses 4) Damage or structural deformation to the structural members, the cylinder brac

51 In normal use the load chains should be re-lubricated every 250 operating hours; in the event of heavy soiling, moisture and very high prolo

52  Chain inspections Chains used in stackers should be inspected at least once a year or every three months if exposed to severe contaminat

53  Temporary lay-up If, for operating reasons, the stacker is laid up for more than two months, the following instructions are

54 Part list Electric circuit

55

56 Part list S-62 Electric component list NO

57 Part list Hydraulic Circuit Diagram

58 Part list

59 Part list

6 Safety notes Symbols and pictograms used In additi

60 Part list

7 Product description Designated use  The stacker is designated fo

8 Product description

9 Removing from the pallet or lifting the product Lifting belt specification— Use polyester